Can a relay be on for 16 hours continuously? The 2019 Stack Overflow Developer Survey Results...
How to delete random line from file using Unix command?
Did the new image of black hole confirm the general theory of relativity?
Are spiders unable to hurt humans, especially very small spiders?
How did the audience guess the pentatonic scale in Bobby McFerrin's presentation?
Keeping a retro style to sci-fi spaceships?
Working through the single responsibility principle (SRP) in Python when calls are expensive
Does Parliament need to approve the new Brexit delay to 31 October 2019?
Who or what is the being for whom Being is a question for Heidegger?
Road tyres vs "Street" tyres for charity ride on MTB Tandem
How can I protect witches in combat who wear limited clothing?
Why is superheterodyning better than direct conversion?
How is simplicity better than precision and clarity in prose?
Is this wall load bearing? Blueprints and photos attached
Netflix Recommendations?
Match Roman Numerals
How do I add random spotting to the same face in cycles?
What's the point in a preamp?
"... to apply for a visa" or "... and applied for a visa"?
Can a relay be on for 16 hours continuously?
How do you keep chess fun when your opponent constantly beats you?
Relations between two reciprocal partial derivatives?
What is special about square numbers here?
How are presidential pardons supposed to be used?
First use of “packing” as in carrying a gun
Can a relay be on for 16 hours continuously?
The 2019 Stack Overflow Developer Survey Results Are In
Announcing the arrival of Valued Associate #679: Cesar Manara
Planned maintenance scheduled April 17/18, 2019 at 00:00UTC (8:00pm US/Eastern)
Congratulation Joan for 50k!16 channel relay for RPiSimple Relay ControlWhat things I can use for turning on a relay?3V3 enough for a 5V relay?Relay boards that can handle 20V 20A DCCircuit complete near high voltage machineComponents for relay setup with Raspberry PiRaspi's USB and Ethernet occasionally shut down when connecting relay boardOpen/Close Sliding Gate Using Raspberry Pi and PythonDetecting electricity via a relay board
.everyoneloves__top-leaderboard:empty,.everyoneloves__mid-leaderboard:empty,.everyoneloves__bot-mid-leaderboard:empty{ margin-bottom:0;
}
A part of my engineering project involves a L.E.D tubelight staying on for 16 hours continuously. I am connecting the light to a relay module. Is it ok, if the relay stays on for so long? I mean, is it designed to sustain for such a huge period of time?
electronics relay
asked 12 hours ago
Aditya RaghuAditya Raghu
142
add a comment |
A part of my engineering project involves a L.E.D tubelight staying on for 16 hours continuously. I am connecting the light to a relay module. Is it ok, if the relay stays on for so long? I mean, is it designed to sustain for such a huge period of time?
electronics relay
asked 12 hours ago
Aditya RaghuAditya Raghu
142
add a comment |
A part of my engineering project involves a L.E.D tubelight staying on for 16 hours continuously. I am connecting the light to a relay module. Is it ok, if the relay stays on for so long? I mean, is it designed to sustain for such a huge period of time?
electronics relay
asked 12 hours ago
Aditya RaghuAditya Raghu
142
A part of my engineering project involves a L.E.D tubelight staying on for 16 hours continuously. I am connecting the light to a relay module. Is it ok, if the relay stays on for so long? I mean, is it designed to sustain for such a huge period of time?
electronics relay
electronics relay
asked 12 hours ago
Aditya RaghuAditya Raghu
142
asked 12 hours ago
Aditya RaghuAditya Raghu
142
asked 12 hours ago
Aditya RaghuAditya Raghu
142
asked 12 hours ago
Aditya RaghuAditya Raghu
142
asked 12 hours ago
Aditya RaghuAditya Raghu
142
142
add a comment |
add a comment |
2 Answers
2
active
oldest
votes
The first stop to answer such questions should be the datasheet of the part in question. This is where the manufacturer lists the operating conditions of the device.
That aside it is usually safe to have a relay active for longer periods of time, assuming you're within the operational range of current and voltage (again, as laid out in the datasheet).
Wear and tear of an electromechanical relay is usually due to switching under load, i.e. with a voltage applied to the terminals, not being permanently on or off. For more on the issue of contact degradation see here https://en.wikipedia.org/wiki/Relay#Arcing (which I won't make part of this answer as it does not address the question).
answered 11 hours ago
Ghanima♦Ghanima
12.5k114080
Thank you so much for your help @Ghanima. Btw does a timer relay also have the same working?
– Aditya Raghu
11 hours ago
add a comment |
To add to @Ghanima's excellent answer, you may also wish to consider a latching relay. Briefly, a latching relay has two stable states (i.e. it is a bistable device, similar to a flip-flop). This means that the relay can be latched into an OPEN or CLOSED state, and it will remain in that state until commanded to change by the input. This avoids the necessity of supplying input voltage and current to maintain (for example) a NORMALLY OPEN relay in a CLOSED state for an extended period of time. Latching relays typically find application in situations similar to the one you've described in your question - where they must be in an OPEN or CLOSED state for extended periods of time.
answered 50 mins ago
SeamusSeamus
3,0671322
add a comment |
Your Answer
StackExchange.ifUsing("editor", function () {
return StackExchange.using("schematics", function () {
StackExchange.schematics.init();
});
}, "cicuitlab");
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "447"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fraspberrypi.stackexchange.com%2fquestions%2f96471%2fcan-a-relay-be-on-for-16-hours-continuously%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
2 Answers
2
active
oldest
votes
2 Answers
2
active
oldest
votes
active
oldest
votes
active
oldest
votes
The first stop to answer such questions should be the datasheet of the part in question. This is where the manufacturer lists the operating conditions of the device.
That aside it is usually safe to have a relay active for longer periods of time, assuming you're within the operational range of current and voltage (again, as laid out in the datasheet).
Wear and tear of an electromechanical relay is usually due to switching under load, i.e. with a voltage applied to the terminals, not being permanently on or off. For more on the issue of contact degradation see here https://en.wikipedia.org/wiki/Relay#Arcing (which I won't make part of this answer as it does not address the question).
answered 11 hours ago
Ghanima♦Ghanima
12.5k114080
Thank you so much for your help @Ghanima. Btw does a timer relay also have the same working?
– Aditya Raghu
11 hours ago
add a comment |
The first stop to answer such questions should be the datasheet of the part in question. This is where the manufacturer lists the operating conditions of the device.
That aside it is usually safe to have a relay active for longer periods of time, assuming you're within the operational range of current and voltage (again, as laid out in the datasheet).
Wear and tear of an electromechanical relay is usually due to switching under load, i.e. with a voltage applied to the terminals, not being permanently on or off. For more on the issue of contact degradation see here https://en.wikipedia.org/wiki/Relay#Arcing (which I won't make part of this answer as it does not address the question).
answered 11 hours ago
Ghanima♦Ghanima
12.5k114080
Thank you so much for your help @Ghanima. Btw does a timer relay also have the same working?
– Aditya Raghu
11 hours ago
add a comment |
The first stop to answer such questions should be the datasheet of the part in question. This is where the manufacturer lists the operating conditions of the device.
That aside it is usually safe to have a relay active for longer periods of time, assuming you're within the operational range of current and voltage (again, as laid out in the datasheet).
Wear and tear of an electromechanical relay is usually due to switching under load, i.e. with a voltage applied to the terminals, not being permanently on or off. For more on the issue of contact degradation see here https://en.wikipedia.org/wiki/Relay#Arcing (which I won't make part of this answer as it does not address the question).
answered 11 hours ago
Ghanima♦Ghanima
12.5k114080
The first stop to answer such questions should be the datasheet of the part in question. This is where the manufacturer lists the operating conditions of the device.
That aside it is usually safe to have a relay active for longer periods of time, assuming you're within the operational range of current and voltage (again, as laid out in the datasheet).
Wear and tear of an electromechanical relay is usually due to switching under load, i.e. with a voltage applied to the terminals, not being permanently on or off. For more on the issue of contact degradation see here https://en.wikipedia.org/wiki/Relay#Arcing (which I won't make part of this answer as it does not address the question).
answered 11 hours ago
Ghanima♦Ghanima
12.5k114080
answered 11 hours ago
Ghanima♦Ghanima
12.5k114080
answered 11 hours ago
Ghanima♦Ghanima
12.5k114080
answered 11 hours ago
Ghanima♦Ghanima
12.5k114080
12.5k114080
Thank you so much for your help @Ghanima. Btw does a timer relay also have the same working?
– Aditya Raghu
11 hours ago
add a comment |
Thank you so much for your help @Ghanima. Btw does a timer relay also have the same working?
– Aditya Raghu
11 hours ago
Thank you so much for your help @Ghanima. Btw does a timer relay also have the same working?
– Aditya Raghu
11 hours ago
Thank you so much for your help @Ghanima. Btw does a timer relay also have the same working?
– Aditya Raghu
11 hours ago
add a comment |
To add to @Ghanima's excellent answer, you may also wish to consider a latching relay. Briefly, a latching relay has two stable states (i.e. it is a bistable device, similar to a flip-flop). This means that the relay can be latched into an OPEN or CLOSED state, and it will remain in that state until commanded to change by the input. This avoids the necessity of supplying input voltage and current to maintain (for example) a NORMALLY OPEN relay in a CLOSED state for an extended period of time. Latching relays typically find application in situations similar to the one you've described in your question - where they must be in an OPEN or CLOSED state for extended periods of time.
answered 50 mins ago
SeamusSeamus
3,0671322
add a comment |
To add to @Ghanima's excellent answer, you may also wish to consider a latching relay. Briefly, a latching relay has two stable states (i.e. it is a bistable device, similar to a flip-flop). This means that the relay can be latched into an OPEN or CLOSED state, and it will remain in that state until commanded to change by the input. This avoids the necessity of supplying input voltage and current to maintain (for example) a NORMALLY OPEN relay in a CLOSED state for an extended period of time. Latching relays typically find application in situations similar to the one you've described in your question - where they must be in an OPEN or CLOSED state for extended periods of time.
answered 50 mins ago
SeamusSeamus
3,0671322
add a comment |
To add to @Ghanima's excellent answer, you may also wish to consider a latching relay. Briefly, a latching relay has two stable states (i.e. it is a bistable device, similar to a flip-flop). This means that the relay can be latched into an OPEN or CLOSED state, and it will remain in that state until commanded to change by the input. This avoids the necessity of supplying input voltage and current to maintain (for example) a NORMALLY OPEN relay in a CLOSED state for an extended period of time. Latching relays typically find application in situations similar to the one you've described in your question - where they must be in an OPEN or CLOSED state for extended periods of time.
answered 50 mins ago
SeamusSeamus
3,0671322
To add to @Ghanima's excellent answer, you may also wish to consider a latching relay. Briefly, a latching relay has two stable states (i.e. it is a bistable device, similar to a flip-flop). This means that the relay can be latched into an OPEN or CLOSED state, and it will remain in that state until commanded to change by the input. This avoids the necessity of supplying input voltage and current to maintain (for example) a NORMALLY OPEN relay in a CLOSED state for an extended period of time. Latching relays typically find application in situations similar to the one you've described in your question - where they must be in an OPEN or CLOSED state for extended periods of time.
answered 50 mins ago
SeamusSeamus
3,0671322
answered 50 mins ago
SeamusSeamus
3,0671322
answered 50 mins ago
SeamusSeamus
3,0671322
answered 50 mins ago
SeamusSeamus
3,0671322
3,0671322
add a comment |
add a comment |
Thanks for contributing an answer to Raspberry Pi Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fraspberrypi.stackexchange.com%2fquestions%2f96471%2fcan-a-relay-be-on-for-16-hours-continuously%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
